Waste Scrap aluminum shredding machine

Product introduction

Scrap aluminum shredding machine is also known as aluminum alloy shredding machine, is a rolling knife shaft through the generation of shear force, will be a large number of scrap aluminum material shredding machine equipment to a certain size, with electrostatic and specific gravity separator will be completely separated from aluminum, suitable for a variety of aluminum materials crushing separation screening operations.

Principle of equipment

Aluminium scrap shredding machine (aluminium alloy shredding machine) with eddy current separator, screening machine, magnetic separator, which can effectively separate the aluminum, iron, paint will be all kinds of scrap aluminum alloy pieces, magnetic separation, screening, cleaning processing, non-metallic impurities removing metal impurities and waste, realize the separation of waste aluminum and recycling, sorting rate can reach 96-99%, maximum get pure aluminum into the next phase of smelting recovery, the aluminium scrap shredding machine effectively provide aluminium scrap recycling efficiency, reduce waste aluminum transportation cost, storage cost.

Characteristics of the equipment

1. The blade is made of cold die steel with good strength, high toughness and high cutting performance. The blade has four cutting edges and can be rotated 90° after wear for continued use.

2. Hydraulic forced feeding, stable and adjustable speed, large and even propulsion force

3. Hard tooth surface reducer, high transmission efficiency, strong bearing capacity and low noise.

4. Blade thickness: 20mm (customized according to customer needs)

5. Scrap aluminum shredder (aluminum alloy shredder) can be easily replaced after the tool damage or wear.

Equipment maintenance:

1. Fix the equipment on the foundation, start the air machine first, and check whether the parts are deformed or damaged during transportation.

2. During operation, the bearing and reducer shall be filled with quantitative lubricating oil. During normal operation, the material conveyor shall be cut out first, and the equipment shall be moved.

3. Before starting up each shift, check the lubrication of the bearing. At the end of each shift, clean the equipment carefully.

Applicable materials:

Is suitable for the aluminium scrap, such as aluminum, aluminum alloy, aluminum plate, aluminum scrap, aluminum wire, aluminum cans, aluminum scraps, Aluminum Casting, aluminum tubes, scrap aluminium wire, aluminum mold, stamping aluminum, mechanical raw aluminum, aluminum foil, PS version, scrap aluminum, cooked aluminum, aluminum slag, scrap aluminum ash, waste aluminum, waste aluminum, scrap aluminum mold, waste PS plate, such as aluminum scrap aluminium wire materials, smashing into a state of separation, the corresponding sorting equipment for aluminum separation, separation rate can reach 96-99%.

Safety rules:

1, after starting, for the machine to run properly,  allowed uniform continuous feed crops.
2, pay attention to the speed of the motor, when working  voice and the temperature of the bearing.
3. When feeding, the operator should stand on one side of the feeding mouth, tighten the sleeves of the clothes, and wear a mask and working cap.
4, feeding, attention should be paid to inputs if there is a stone inside, sickle,  tools with hard objects, such as screw, in order to avoid damage to the machine and cause accidents.
5. No belt hanging, oiling, cleaning and troubleshooting are allowed when the machine is running.
6, found the following problems should be shut down the engine, stop processing, motor smoke, crush quality is not good, bearing overheating, more than 60 degrees.

Strictly prohibited items:

1. It is strictly forbidden to peep into the machine from the upper part of the broken cavity during operation.
2. electrical equipment should be connected to the ground, wire insulation should be reliable and installed in the steel pipe laying.
3. It is strictly forbidden to move or remove materials directly by hand in the crushing cavity behind the feeding port during operation.
4. the mill in the operation of any adjustment, cleaning or maintenance work is strictly prohibited.

Pre-sale:
(1) selection of equipment type.
(2) Design and manufacture products according to the special requirements of customers.
(3) training of technical personnel for clients.
(4) The company plans the site for the user free of charge, designs the suitable process and the plan.
On sale:
(1) acceptance of the product.
(2) assisting clients in the preparation of construction plans.
After sale:
(1) assign special after-sales service personnel free of charge to guide customers to install and debug.
(2) installation and debugging of equipment.
(3) on-site training of operators.
(4) after the installation of the complete set of equipment, the full-time technical personnel may assist the customer in on-site production until the user is satisfied.

Contact us if you need more details on Scrap Aluminum Shredding Machine. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Aluminium Shredding Machine、Waste Aluminum Shredding Machine. If these products fail to match your need, please contact us and we would like to provide relevant information.

Product Categories : Shredder Machine > Aluminium Shredder